
THE SHORT ANSWER
Enter the 17-character VIN in NHTSA's vPIC tool and read the prefix first. Kenworth Truck Company holds four truck prefixes (1XK, 2XK, 3WK, SFN), Kenworth Mexicana SA de CV holds three (3WM, 3NM, 3XK), and four more (1NK, 2NK, 3BK, 3NK) mark incomplete vehicles. The decode costs nothing and reports the truck as built, so it says nothing about accidents, title brands, liens or mileage.
- Prefixes in the register
- Eleven, under two registered company names
- Kenworth Truck Company
- 1XK, 2XK, 3WK and SFN for trucks
- Kenworth Mexicana
- 3WM, 3NM and 3XK for trucks
- Incomplete vehicles
- 1NK, 2NK, 3BK and 3NK
The first three characters name the builder
Under the federal VIN rule, the opening section of a VIN is three characters long and identifies the manufacturer and the type of vehicle. NHTSA publishes those assignments, and vPIC reads them back when you enter a VIN. The first character doubles as a region marker: a 1 points to the United States, a 2 to Canada and a 3 to Mexico, with 4 and 5 as more United States digits.
For Kenworth, the third character carries the brand letter. Eight of the eleven registered prefixes end in K, a handy sanity check on a VIN copied by hand. Only the full three characters, matched against the register below, settle it.
All eleven Kenworth prefixes as vPIC lists them
NHTSA's manufacturer lookup returns eleven prefixes for Kenworth: four trucks from Kenworth Truck Company, three trucks from Kenworth Mexicana SA de CV, and four incomplete vehicles.
| Prefix | Registered name | Type in register | Country in register |
|---|---|---|---|
| 1XK | Kenworth Truck Company | Truck | United States |
| 2XK | Kenworth Truck Company | Truck | Canada |
| 3WK | Kenworth Truck Company | Truck | Mexico |
| SFN | Kenworth Truck Company | Truck | United Kingdom |
| 3WM | Kenworth Mexicana SA de CV | Truck | Mexico |
| 3NM | Kenworth Mexicana SA de CV | Truck | None listed |
| 3XK | Kenworth Mexicana SA de CV | Truck | Mexico |
| 1NK | Kenworth Truck Company | Incomplete vehicle | United States |
| 2NK | Kenworth Truck Company | Incomplete vehicle | Canada |
| 3BK | Kenworth Truck Company | Incomplete vehicle | Mexico |
| 3NK | Kenworth Mexicana SA de CV | Incomplete vehicle | Mexico |
The country column is NHTSA's own entry, a hint about where a prefix was assigned rather than proof of where your truck was assembled. The decoded plant city and country are better evidence when vPIC supplies them.
Kenworth Mexicana is a separate registrant
Kenworth Mexicana SA de CV does not sit inside Kenworth Truck Company's registration as a plant code. NHTSA lists it as a manufacturer in its own right, and a decode of 3WM, 3NM, 3XK or 3NK names that company. The parent field in vPIC shows PACCAR Inc. for Kenworth Truck Company and Peterbilt Motors Company, and none for the Mexicana entries.
Do not stop at the leading 3. Two Kenworth Truck Company prefixes, 3WK and 3BK, also start with it and list Mexico as their country. The prefix 3NM, registered to Kenworth Mexicana, shows no country at all. Read all three characters every time.
Provenance, not a quality grade
The prefix tells you which registered company stands behind the build. By itself it reports nothing about different specifications, standards or components, so treat it as a paperwork detail worth knowing before a lender or insurer asks.
When the result says incomplete vehicle
Four prefixes, 1NK, 2NK, 3BK and 3NK, are registered as incomplete vehicles rather than trucks. Federal definitions describe one as a chassis assembly (frame, power train, steering, suspension and brakes) that still needs further manufacturing before it counts as complete.
A decode that describes a bare chassis while a finished truck sits in front of you usually means a later builder added the body, cab or equipment. The VIN does not change when that happens. The rules assign the number to the incomplete vehicle manufacturer, and anyone who alters the vehicle afterward must keep it.
The decoded fields then describe what Kenworth shipped, not what the final builder delivered, so get the finished configuration from that builder's documents.
A shared parent, but separate prefixes from Peterbilt
Peterbilt Motors Company is registered on its own, and its truck and incomplete-vehicle prefixes mirror Kenworth Truck Company's: 1XP, 2XP, 3WP, 1NP, 2NP and 3BP set against 1XK, 2XK, 3WK, 1NK, 2NK and 3BK. Only the final letter differs, so once you read the third character a Kenworth VIN cannot pass for a Peterbilt one.
The shared parent matters more in recall records. NHTSA files Kenworth campaigns under PACCAR Incorporated, and several notices name Kenworth and Peterbilt models together, frequently because one engine, brake or electrical component sits behind both. A news item about the other brand can still reach your truck, so search by your own VIN rather than the badge.
What the other fourteen characters tell you
For a truck, the federal rule requires the maker to be able to explain positions 4 through 8 in terms of model or line, series, chassis, cab type, engine type, brake system and weight rating. That is why a decode of a heavy truck often returns more than make and year: cab layout, engine maker and size, brake type and weight class.
- Position 9 is the check digit, a calculated value that exposes transcription errors.
- Position 10 is the model year code, and position 11 is the plant of manufacture.
- Positions 12 through 17 are the production sequence number. On a heavy truck only the last four of them must be numeric.
- The letters I, O and Q are never used, so one in your copy of the VIN is a misread.
Checking the number against the label and the frame
On a truck Kenworth finished itself, the certification label is the best second witness for a VIN. Federal rules put it on the hinge pillar, door-latch post or door edge beside the driver's seat, with the left side of the instrument panel as the fallback. It must show the manufacturer's name after the words Manufactured By, the month and year of manufacture, the weight rating, each axle's rating and the VIN.
The name on the label is normally the actual assembler, though a controlling corporation that takes responsibility for conformity may be named instead. A label and a prefix that seem to disagree call for a question, not a conclusion.
Do not count on a plate at the base of the windshield. The rule that makes a VIN readable through the glass covers cars and other light vehicles. A heavy truck only needs the number on a part not meant to be removed, or on a permanently attached plate.
- Photograph the label and the stamped number close up, in good light.
- Compare the characters with the title or registration, one position at a time.
- Enter the VIN in vPIC and read the error text as well as the fields.
- If vPIC says the check digit does not calculate, re-read the characters before blaming the truck.
The VIN is not the only number on the truck
Someone who types Kenworth chassis number into a search box is nearly always after the VIN. On a truck titled in the United States, that 17-character string is what a title, a registration and a recall search all use. Engines, transmissions and axles carry separate identifiers that no VIN decoder reads.
| Number | Where it is found | What it is for |
|---|---|---|
| VIN | Certification label, frame, paperwork | Title, registration, recall search, decoding |
| Engine serial | Stamped or tagged on the engine | Ordering engine parts |
| Transmission serial | On the transmission case | Ordering parts for the right ratio set |
| Axle tags | Fitted to each axle | Axle parts and ratios |
Trucks that have worked for years drift away from the factory build. A repowered engine or a rebuilt transmission is ordinary, while the VIN keeps describing the original specification. When a decode names an engine, confirm it against the serial on the engine itself.
Checks to run before paying for a used Kenworth
Decode before anything else. It costs nothing and catches listing errors such as a wrong model year, engine or cab. Then check the hardware against the decode, not the other way round.
Run the NHTSA recall search with the same VIN. Heavy trucks are in NHTSA's recall data, and Kenworth campaigns are filed under PACCAR Incorporated. A manufacturer must remedy a recall defect at no charge to the owner, with a limit: the duty does not apply when the first buyer purchased the vehicle more than 15 calendar years before the recall notice. That clock starts at the first retail sale, not at your purchase, so ask what a repair would cost if the truck is that old.
A heavy truck that has worked in commerce generally falls under federal motor carrier safety rules, so ask for its inspection and maintenance records rather than a verbal history.
What no decoder can tell you
A decode describes the build as it left the factory. It does not know about a collision, a salvage brand, a lien or how far the truck has run, and a working truck has had years to collect all four.
Mileage is the widest gap. Under the federal odometer rules, a seller need not state the mileage for a vehicle rated above a set weight, so a Class 8 tractor can be sold without any mileage statement. Older vehicles are exempt by age as well. Ask for service invoices that record mileage and compare them with the dash.
Public tools fill part of the gap. NICB's VINCheck covers theft and salvage reports at no charge, and the federal NMVTIS database holds title records that approved providers make available. A vehicle history report from yourvinhistory adds accident, odometer, auction and lien records for the VIN where they were reported; the preview step costs nothing and the full report is a one-time purchase.
Where this information comes from
- NHTSA: vPIC VIN decoder and manufacturer register — Where the eleven Kenworth prefixes, their registered names, vehicle types and countries were read, and the decoder that returns the fields for a full VIN.
- NHTSA: Recalls lookup by VIN — The federal open-recall search. Kenworth truck campaigns appear in this data under the PACCAR name.
- eCFR: VIN requirements for motor vehicles — Backs the points on what positions 4 to 8 must encode, the check digit, the letters that are never used, and where a VIN has to appear.
- eCFR: Certification label contents and location — Shows where the label sits near the driver's seat and what it must state, including the builder's name and the VIN.
- U.S. Code: Notification and remedy of defects — Sets the no-charge recall remedy and the age limit measured from the first purchase.
- eCFR: Odometer disclosure exemptions — Lists the vehicles, including heavier ones and older ones, whose sellers need not state the mileage.
Sources and photos: Facts checked against the sources above in October 2026. Photo by fr0ggy5 on Unsplash; diagrams by YourVINHistory.
Keep reading
- Semi trucksGoes further into the separate serial numbers on a single heavy truck.
- PeterbiltCovers the sister PACCAR brand and its own pair of prefixes.
- How to read a VINWalks through all 17 positions, the year chart and the check digit.
- Recall check by VINExplains why a search by VIN and a search by model give different recall results.
Frequently asked questions
What does 1XK mean at the start of a Kenworth VIN?
It is the manufacturer prefix NHTSA registers to Kenworth Truck Company for trucks, with the leading 1 pointing to the United States. The K in third place is Kenworth's letter, the slot where Peterbilt uses P. The prefix does not carry the model or year, so run all 17 characters through vPIC to see those.
Does a VIN beginning with 3 mean my Kenworth was built in Mexico?
Usually the register points that way, but not always. The prefixes 3WK and 3BK begin with a 3, list Mexico and belong to Kenworth Truck Company, while 3NM belongs to Kenworth Mexicana with no country shown. For firmer evidence, read the full prefix, the Manufactured By line on the label and the plant location vPIC returns.
Why does the decode list a different engine than the one in my truck?
A VIN describes the engine fitted when the truck left the factory. If the engine was replaced or rebuilt into a different configuration later, the decode will not show it. Check the serial on the engine, ask for the repower invoice, and treat a mismatch as a pricing and parts question, not a sign the VIN is wrong.
Can I decode a Kenworth VIN without paying or signing up?
Yes. NHTSA's vPIC is a public tool that takes a VIN and returns what the maker filed, which for a heavy truck can include weight class, cab type, engine, brake type and assembly plant. It is not a history check, so it will not mention recalls, accidents or ownership. Recalls are a separate NHTSA search that also takes the VIN.
Is a Kenworth with an incomplete-vehicle prefix a problem?
Not by itself. The prefix means Kenworth supplied the chassis to be finished by another builder, so the decode describes the chassis only. What to verify is the finished truck: match the final builder's documents to what is on the road, and confirm that the VIN on the frame agrees with the title.
Now check the car itself
The guide explains what to look for. The report shows what this VIN has on record.