
THE SHORT ANSWER
RepairPal lists $979 to $1,150 nationally for an F-150 water pump, made up of $682 to $713 in parts and $298 to $437 in labor. Kelley Blue Book's 2020 page shows a general $375 to $787. Ford's Motorcraft listings describe pulley-flange pumps for the 5.0L V8 and the smaller 2.7L, 3.3L and 3.5L engines, which means belt drive and outside mounting. No NHTSA recall names the pump.
- RepairPal national range
- $979 to $1,150
- Labor share
- $298 to $437
- Pump recalls found
- None, model years 2008 to 2022
- Ford pump listings checked
- 4 with pulley flanges
Two published ranges, and who stands behind each
No price here is ours or a shop's; each belongs to the publisher named beside it. For the F-150, RepairPal's estimator is the only source with a truck-specific number: $979 to $1,150 nationally. Its page says it was last updated September 3, 2026. Its year-by-year rows displayed inconsistently, so only the national range is used.
| Piece of the job | RepairPal, national |
|---|---|
| Parts | $682 to $713 |
| Labor | $298 to $437 |
| Whole job | $979 to $1,150 |
Kelley Blue Book's only number comes from a 2020 F-150 SuperCrew page: a general $375 to $787, with no local pricing behind it. Use either range to size up a quote, not to set one.
Why labor stays small on this truck
A pump mounted outside the engine and spun by the accessory belt is a different job from one tucked behind the timing cover. In RepairPal's F-150 estimate the labor line sits under the parts line, which is the pattern an accessible pump should produce.
Same maker, much higher labor
RepairPal's 2019 Explorer page lists $1,281 to $1,880 for labor alone. The Explorer, Edge, Flex and Taurus share a transverse 3.5L Duratec V6 with its pump behind the timing cover, driven by the chain. When that design fails, coolant can reach the engine oil. F-150 engines are mounted lengthwise and use different pumps.
So an F-150 quote with Explorer-sized labor deserves questions: another engine, timing work folded in, or a part Ford does not list.
What Ford's Motorcraft listings say about the drive
Ford's own parts catalog on ford.com gives the firmest evidence of belt drive. Each Motorcraft pump listed for the F-150 names a pulley flange, the mount a drive belt spins. The Duratec pump included as a control names a sprocket instead.
| Engine in the listing | Motorcraft part | Drive hardware named |
|---|---|---|
| 3.5L, Expedition, F-150, Transit | PW568 | Three-bolt pulley flange |
| 3.3L and 3.5L F-150, 3.7L Transit | PW591 | Three-bolt pulley flange |
| 2.7L F-150 | PW632 | Three-bolt pulley flange |
| 5.0L F-150 and Mustang | PW535 | Four-bolt pulley flange |
| 3.5L Duratec (control) | PW683 | Single-tooth sprocket, chain-driven |
No F-150 listing uses sprocket wording. The listings name engines, but their fitment tables did not display, so this guide ties each pump to an engine, not to a model year.
Match the engine to the job before you compare quotes
The F-150 has had many engines since 2008, and the pump you are pricing depends on yours. EPA's fueleconomy.gov records list what Ford certified each year.
| Model years | Engines certified |
|---|---|
| 2008 to 2010 | 4.6L V8, 5.4L V8, and a 4.2L V6 in 2008 only |
| 2011 to 2014 | 5.0L V8, 6.2L V8, 3.7L V6 and the 3.5L EcoBoost |
| 2015 to 2017 | 5.0L V8, 3.5L V6, plus the 2.7L and 3.5L EcoBoost |
| 2018 to 2020 | 3.0L diesel, 3.3L V6, 5.0L V8, plus the 2.7L and 3.5L EcoBoost |
| 2021 to 2022 | 3.3L V6, 5.0L V8, 2.7L and 3.5L EcoBoost, a PowerBoost hybrid, and the 3.0L diesel in 2021 |
Ford's catalog supports belt drive for the 2.7L, the two 3.5L engines, the 3.3L and the 5.0L. It settles nothing about the 4.6L, 5.4L, 6.2L, 3.0L diesel or PowerBoost hybrid. If yours is one, ask the shop where the pump mounts and how many labor hours it books.
What 19,248 owner complaints show, and what they can't
NHTSA's complaint files for the 2008 to 2022 F-150 hold 19,248 reports, and 3,530 of them, about 18%, are filed under ENGINE. There is no water pump category. ENGINE collects every engine fault from every engine sold, so it caps what could be pump-related without measuring it, and the reports are unverified.
| Engine lineup | Share filed under ENGINE |
|---|---|
| 2008 to 2010 | 13% |
| 2011 to 2014 | 21% |
| 2015 to 2017 | 19% |
| 2018 to 2020 | 23% |
| 2021 to 2022 | 5%, a minimum |
Even at the 23% peak, 77% of complaints concern something else. Power train reports, which include the transmission, exceed ENGINE reports in 12 of 15 model years and 6,106 to 3,530 overall. The 2021 to 2022 figure is a floor, since ENGINE is not among 2022's top five components. The narrower ENGINE AND ENGINE COOLING category makes a top five only in 2019, at 54 reports; elsewhere it ranks below the fifth, meaning smaller, not zero.
Leaks and warnings Ford ties to parts other than the pump
A coolant puddle under an F-150 is usually pinned on the pump first. Ford's service bulletins, which NHTSA files under each vehicle, describe neighboring faults that cost less to fix.
| Trucks | Ford document | Reported fault |
|---|---|---|
| 2015, 5.0L | Bulletin 15-0073 | Heater hose pulling off its outlet tube at the coolant pump |
| 2021, 3.5L EcoBoost and PowerBoost | TSB 21-2373 | Degas bottle hose leaking toward the thermostat housing, built through March 31, 2021 |
| 2021 to 2022, 3.5L EcoBoost | SSM 50835 | Thermostat housing leaking at an incomplete weld, built through March 8, 2022 |
| 2.7L EcoBoost | SSM 47791 and TSB 21-2168 | Temperature warnings and sensor codes blamed on wiring or voltage |
| 2019 to 2020, 3.3L | TSB 20-2292 | Heat that comes and goes: software left the auxiliary coolant pump idle at stop-start |
Each row names a cheaper suspect: a heater hose on the 2015 5.0L, the degas hose or thermostat housing on the 2021 3.5L, the sensor circuit on the 2.7L. Before approving a pump, ask what the shop ruled out and have it show you where the coolant is actually escaping.
No recall names the F-150 water pump
Searching NHTSA's recall data across the 2008 through 2022 model years turns up no F-150 campaign whose summary mentions the water pump. Run against a 2012 BMW 328i, the same method does find a pump recall. Two F-150 campaigns do sit under NHTSA's engine-cooling heading, but neither is about the pump: 08V523 applies to 213 trucks of 2007 to 2008 vintage that Roush set up for propane, and 24V635 involves a 2.7L or 3.0L engine in 2021 to 2022 trucks, where intake valves may break.
Absent another program, a pump failure is an out-of-pocket repair.
- Recall: a safety-defect repair a dealer performs at no charge within the federal rule's limits; this pump has none.
- Service bulletin: repair steps and labor times, with no payment once the truck is out of warranty.
- Factory warranty: pays for a failed pump if the truck is within Ford's coverage terms.
- Goodwill: a case-by-case call by dealer and Ford, usually near the end of warranty.
NHTSA's recall lookup by VIN shows other open recalls on a specific truck.
When a timing job is already open, ask about the pump
Outside-mounted does not mean unrelated to timing work. On the 3.5L EcoBoost the pump attaches to the engine's front cover. Ford's Customer Satisfaction Program 21N03, which extends cam phaser coverage on certain 2017 to 2020 3.5L trucks, lists a gasket and an O-ring for the coolant pump among the parts the job uses. Removing the cover means removing the pump.
That reverses the Explorer's logic, where the timing chain gets pulled into every pump job. Here a timing repair is the cheap moment for a pump, because removal labor is already in the quote. Ask for it as its own line. A high-mileage or seeping pump is worth replacing then; a dry, low-mileage one is optional.
Why the coolant on the invoice matters
Program 16U11 covered F-150s built at Ford's Kansas City plant on February 1 and 2, 2016, whose coolant mix might be weaker than specified. Ford lists water pump noise and leaks among the results of a weak mix. A separate 2019 service message says trucks assembled from January 2, 2019 onward received Motorcraft Yellow coolant, and tells shops not to mix colors or types.
Build date therefore decides which coolant a 2019 truck carries, and a mismatched refill adds a second problem. Have the coolant named on the invoice, and confirm the factory fill by VIN.
Warning signs, and the one that means stop driving
- Drips or dried coolant crust low on the front of the engine
- Whining or growling at the front of the engine that follows engine speed
- Pump pulley wobble or play with the engine off
- Coolant level falling in the reservoir between checks
- A climbing temperature gauge or an over-temperature warning
The first four leave time to book a repair. The last does not: a seized pump or a failed seal can overheat an engine quickly, even though external pumps often leak visibly first. If the needle is rising, stop driving and arrange a tow. On a 2.7L, where Ford documented false over-temperature warnings, have the shop take its own reading first.
Checks before you pay for the repair or buy the truck
- Decode the VIN to confirm the engine; part and labor depend on it.
- Ask the shop to show where coolant is escaping.
- On a 2015 5.0L or 2021 to 2022 3.5L, ask if the hose and thermostat housing bulletins were considered.
- Compare quoted labor with RepairPal's $298 to $437 and question anything far higher.
- With timing work planned on a 3.5L EcoBoost, get the pump priced in that same visit.
A pump is among the smaller worries on a used F-150, and an invoice showing a new one with the right coolant settles it. A VIN-based history report covers the rest: title, accident and odometer records plus open recalls. On a newer truck, a warranty check by VIN shows any coverage left.
Where this information comes from
- NHTSA: recalls by vehicle and VIN — The recall lookup behind the finding that no F-150 campaign from 2008 through 2022 names the water pump.
- EPA and DOE: fueleconomy.gov Find a Car — Per-year F-150 engine listings used to group the model years into lineups.
- RepairPal: Ford F-150 water pump estimate — Source of the national price range and its parts and labor split.
- Ford: Motorcraft PW568 water pump listing — Shows the 3.5L F-150 pump built for a three-bolt pulley flange, plus a durability test claim.
- Ford program 21N03 (NHTSA copy) — Cam phaser program for 2017 to 2020 3.5L trucks whose parts list includes a coolant pump gasket and O-ring.
- Ford program 16U11 (NHTSA copy) — Ford's statement that weak coolant concentration can bring on water pump noise or leaks.
Sources and photos: Facts checked against the sources above in October 2026. Photo by Willian Cittadin on Unsplash; diagrams by YourVINHistory.
Keep reading
- Ford F-150 years to avoid: 2013, 2011 and 2018 draw the most complaintsThe full complaint record by model year, well beyond the engine.
- Ford F-150 timing chain replacement cost: what Ford's own hours sayWhat front-cover and chain work costs, since a pump quote can ride along with it.
- Ford Explorer water pump replacement cost, and what the 3.5L V6 changesThe chain-driven internal pump this truck does not use, and why its labor runs higher.
- Coolant type by VINConfirm which coolant a given truck left the factory with before anyone tops it off.
Frequently asked questions
What does it cost to have a Ford F-150 water pump replaced?
RepairPal's national estimate runs $979 to $1,150, split between $682 to $713 for parts and $298 to $437 for labor. Kelley Blue Book offers a general $375 to $787. Neither is a quote for your truck, so ask for an itemized estimate naming the engine and listing pump, labor and coolant separately.
Is the F-150 3.5 EcoBoost water pump internal?
No. The Motorcraft pump Ford lists for the 3.5L F-150 comes with a three-bolt pulley flange, the mount for a belt-driven pulley, and the 2.7L, 3.3L and 5.0L listings read the same way. The internal, chain-driven pump sits on the transverse 3.5L Duratec V6 used in the Explorer, Edge, Flex and Taurus.
Has Ford recalled the F-150 water pump?
No. NHTSA's recall data for 2008 through 2022 contains no campaign summary that names the pump. Ford has instead published service bulletins for neighboring leaks, such as a heater hose on the 2015 5.0L and a weld flaw in the thermostat housing of 2021 to 2022 3.5L EcoBoost trucks. Enter a VIN in NHTSA's lookup for other open recalls.
When does an F-150 water pump usually need replacing?
Ford sets no interval for swapping it, and routine maintenance excludes it. Motorcraft's product pages say its replacement pumps were durability tested to a lifetime equivalent of 10 years and 150,000 miles, a lab benchmark that says little about the original pump in any one truck. Weak coolant concentration is one documented cause of noise and leaks.
Is it smart to add a new pump when a 3.5 EcoBoost gets timing work?
It is worth asking about. Ford's program 21N03 lists a pump gasket and O-ring for the cam phaser job on 2017 to 2020 trucks, so the pump comes off whenever the cover does. With removal labor already in the timing quote, the pump costs mostly the part. At low mileage with no seepage, it is optional.
Now check the car itself
The guide explains what to look for. The report shows what this VIN has on record.