yourVINhistory

Repair costs

Ford F-150 timing chain replacement cost: what Ford's own hours say

RepairPal puts an F-150 timing job at $2,282 to $3,280, with labor making up nearly the whole bill. Ford's own bulletins show why: the chain and cam phaser repairs they document on 2011–2014 and 2017–2020 EcoBoost trucks are booked at 8.9 to 10.1 hours.

Updated October 30, 2026 · Sources cited below

Have a VIN? Check that car

Find the VIN on the driver's door jamb, at the base of the windshield, or on the registration and insurance card.

View sample report
Mechanic inspecting a pickup beside a panel listing three timing chain quote checks

THE SHORT ANSWER

RepairPal prices an F-150 timing job between $2,282 and $3,280, and labor is the bulk of it. Ford's warranty times for its documented chain and phaser repairs run 8.9 to 10.1 hours, which explains why. Gasoline F-150 engines have chains, not belts. The trucks Ford's paperwork singles out are 2011–2014 and 2017–2020 models with the 3.5L EcoBoost.

RepairPal estimate
$2,282 to $3,280, mostly labor
Ford labor times
8.9 to 10.1 hours for chain or phaser jobs
Timing drive
Chain on gasoline F-150s, 2008–2022
Phaser program 21N03
Ended September 1, 2022

What the published estimate covers

The most specific public number for this truck is RepairPal's: $2,282 to $3,280 for the F-150. Parts account for about $147; the other $2,135 to $3,133 is labor. The page showed an October 16, 2025 update date and the figures were retrieved in October 2026, so confirm them on the live page. They are RepairPal's estimates, not measurements made for this article.

The page title says timing belt replacement, yet these gasoline trucks have no belt, so read it as an estimate for the timing drive. On a separate RepairPal page, for a 2020 F-150 front cover gasket, a tensioner replacement appears as a related job at $2,074 to $2,821.

Ford's labor times for each documented job

Ford publishes how long it pays a dealer for a warranty repair. Independent shops use their own labor guides, so treat these hours as a written reference point, not a promise.

Trucks and engineWork the time coversHoursFord document
2011–2014, 3.5L EcoBoostDiagnosis plus the primary timing chain8.9TSB 17-0026
2017–2018, 3.5L EcoBoostFour VCT units plus a PCM reprogram10.0 (Raptor 10.1)TSB 20-2191
2017–2020, 3.5L EcoBoostFour cam phasers9.5Program 21N03
2007–2010, 5.4L 3VBoth VCT oil control solenoids3.6TSB 12-7-10

Reaching the chain means taking apart the front of the engine, which is where the money goes. Multiply your truck's hours by the shop's posted rate for a fair yardstick on the labor line. A quote well past it either includes extra parts or prices another job.

No timing belt, and one diesel question

Gasoline F-150s from 2008 through 2022 time their valves with chains. That covers the EcoBoost V6s between 2.7L and 3.5L, the 3.3L and 3.7L V6 engines, and the 4.6L, 5.0L, 5.4L and 6.2L V8s. A quote that says belt on any of them is a labeling slip.

The diesel is the open question. Online reports call the 3.0L Power Stroke, offered 2018 through 2021, belt-driven, but no Ford document confirming that turned up, so treat it as unverified and have a dealer check the timing drive by VIN.

Where the engine complaints bunch up

A tally of NHTSA owner complaints against 2008–2022 F-150s holds 19,248 reports, and at least 3,530 are filed under ENGINE. By model year they form two humps that line up with Ford's bulletin years: the 2011–2014 trucks hold 47% of engine reports and the 2017–2020 trucks hold 30%. That puts 77% inside eight of the fifteen model years, which average about 338 reports each against about 118 for the rest.

Model yearENGINE complaintsNote
2011477First EcoBoost year
2013531Peak of the whole run
2014163In the bulletin range, yet low
2018444Peak of the second hump
2008–2010203Three years combined

These are unverified owner reports, not failure rates. ENGINE spans every engine sold that year, so the 2013 figure also holds 5.0L and 3.7L trucks, and the overlap does not prove each report is a stretched chain. For 2022, ENGINE fell below that year's fifth-ranked component and has no count, so the totals are minimums.

2011–2014 EcoBoost: the worn primary chain bulletin

The 3.5L twin-turbo V6 joined the F-150 lineup for 2011, and engine complaints leap from 108 on the 2010 truck to 477 on the 2011. Ford issued TSB 17-0026 on March 8, 2017, replacing 15-0044, for 2011–2014 trucks with that engine and a build date of October 10, 2014 or earlier. The symptom is a warning lamp with code P0016, and Ford says a worn primary chain may be behind it.

A technician must confirm three things before ordering parts: the code is stored, the build date qualifies, and an intake cam reading taken with the engine running is six degrees or more. The repair uses a chain tensioner kit plus gaskets, a filter and fluids, and the 8.9 hours cover diagnosis and replacement together. Warranty status is standard new-vehicle and emissions coverage, and no extended program was found, so on a truck this old the owner usually pays.

2017–2020 EcoBoost: phaser rattle and a program that ended

The second hump peaks at 444 engine reports on the 2018 truck. The noise comes from the cam phasers, adjustable timing units on the camshafts. Ford's TSB 20-2191, issued June 4, 2020, targets 2017 and 2018 F-150s with the 3.5L and a build date of July 10, 2018 or earlier: a tick or rattle lasting two to five seconds on the first start after sitting six hours or more. The repair swaps four VCT units, updates the PCM calibration and leaves other timing parts alone unless Ford lists them. Expect firmer shifts for several days afterward.

Reflash under program 21B10 by August 31, 2021 was the price of entry to 21N03, which paid for phaser replacement on a mileage-prorated basis until September 1, 2022. Both programs date from March 2, 2021 and cover 2017–2020 F-150s with a build date up to November 30, 2019, Raptor and Limited excluded. Ford said the noise does not affect safety, performance or emissions, so it chose a program, not a recall.

Phaser coverage has ended

Program 21N03 stopped on September 1, 2022. Since then a phaser job on a qualifying truck is paid for by the owner, unless Ford or a dealer agrees to a goodwill repair. A seller who says the phasers are still covered by Ford is relying on outdated information.

2008–2010 with the 5.4L: try the solenoids first

Start-up rattle is an old complaint on the 5.4L three-valve V8, but most of its history falls on earlier trucks; the 2008–2010 F-150s are the quietest years in the tally, with 203 engine reports over three model years. Ford's TSB 12-7-10, from July 23, 2012, covers 2004–2010 trucks that rattle intermittently or idle roughly once warm, sometimes with P0021, P0022, P0340 or P0341 stored. It blames oscillating cam timing, and the remedy is not a chain: both VCT oil control solenoids are replaced, booked at 3.6 hours on 2007–2010 trucks. That is a fraction of a timing job, so ask what diagnosis points to the bigger repair.

Recalls, programs and bulletins pay differently

Searching NHTSA recall data one model year at a time, 2008 through 2022, turned up no campaign aimed at the timing chain, tensioner or cam phasers. Two engine recalls look similar but are not. Campaign 17V672 concerns 2018 trucks with the 3.5L whose cylinder heads may lack oil supply holes at the camshaft bearings, a lubrication defect and not a stretched chain. Campaign 24V635 reaches 2021–2022 F-150s running either the 2.7L or 3.0L EcoBoost, where an intake valve may break. Neither covers a timing chain.

MechanismWho paysThe catch
Safety recallManufacturer, via a dealerFederal rules cap vehicle age for a no-charge remedy
Satisfaction programFord, within set dates and mileage21N03 closed in 2022
Service bulletinNo one; it gives steps and labor timeWarranty status decides payment
GoodwillFord or the dealer, by choiceUsually near the end of coverage

Many model years carry campaigns on other systems, so enter the VIN in NHTSA's recall lookup.

Signs to act on, and what to ask the shop

  • 2011–2014 EcoBoost: a lit warning lamp and stored code P0016, sometimes with rough driveability
  • 2017–2018 EcoBoost: a tick, tap or rattle at the front of the engine for a few seconds after a long sit
  • 2017–2020 EcoBoost: rattling on a cold start, or a knock once the engine idles warm
  • 2007–2010 5.4L: a rattle that comes and goes, or a rough idle, once the engine is hot

P0016 means the engine computer found crank and cam positions out of step. Before approving any job:

  1. Confirm engine and build date from the VIN; both bulletins stop at a cutoff.
  2. Have the codes scanned and keep the printout.
  3. Ask which Ford document the shop follows and compare the quote with its parts list.
  4. With a 2017–2020 truck, check whether the price covers just the four phasers or chains and guides too.
  5. Hold the quoted labor hours against Ford's 8.9 to 10.1.

Some shops add chains, guides and tensioners while the engine front is open. That can suit a high-mileage truck, but it should be your choice, with its own line on the quote.

If you are shopping for the truck instead

The same record doubles as a shopping list. On an EcoBoost from 2011–2014 or 2017–2020, ask for proof the bulletin work was done, or price the truck as though it still lies ahead. Decode the VIN for engine and build date, since each bulletin stops at a cutoff.

Arrange to start it cold after an overnight sit and listen to the opening seconds. Then drive through the gears: in 12 of the fifteen model years owners filed more power train complaints than engine ones.

Title history affects factory help too. Ford's letter for program 21N03 has a heading for title-branded and salvaged vehicles, under which it says vehicles with cancelled warranties are not eligible. A history report for the VIN shows title brands, accidents, odometer readings and salvage records, and a preview comes before any purchase.

Where this information comes from

Sources and photos: Facts checked against the sources above in October 2026. Photo by Mustafa Sheikhmouss on Unsplash; diagrams by YourVINHistory.

Keep reading

Frequently asked questions

How much to replace a timing chain on an F-150?

RepairPal prices the job between $2,282 and $3,280, about $147 of it parts, though its page calls the work a timing belt replacement. To test a quote, take Ford's hours for your engine and year (8.9 for the 2011–2014 chain job, 9.5 to 10.1 for phaser work), multiply by the shop's hourly rate and add parts and fluids.

Are timing chain problems common on the 3.5L EcoBoost F-150?

Ford has documented two patterns: a worn primary chain with code P0016 on 2011–2014 trucks, and phaser noise on 2017–2020 trucks. Those eight model years account for 77% of the engine complaints on record, yet that count covers every engine sold in them, and complaints are not failure rates.

Is there a timing belt on an F-150, and what does replacing it cost?

On a gasoline F-150 there is no belt to replace, so the figure to use is the chain job priced in the first answer. If a shop writes timing belt on an estimate, ask which parts it means: chain, tensioner, guides or phasers. The 3.0L Power Stroke diesel is the open question, since reports calling it belt-driven could not be checked against a Ford document.

Does Ford still cover F-150 cam phaser replacement?

No. Customer Satisfaction Program 21N03 ran until September 1, 2022 and applied only to 2017–2020 trucks that had the 21B10 reflash by August 31, 2021. Ford paid all of the repair up to 69,999 miles, 66% through 79,999, 33% through 89,999, and nothing beyond that. It was a one-time repair that passed to later owners, and Raptor and Limited trucks were excluded.

Does a recall or warranty cover an F-150 timing chain?

Not on the records found. No NHTSA recall campaign for 2008–2022 F-150s names the timing chain or phasers, and TSB 17-0026 offers only the standard new-vehicle and emissions warranty eligibility. Run the VIN through NHTSA's recall lookup anyway, since open campaigns on other systems are common, and ask a dealer about goodwill before you pay.

Now check the car itself

The guide explains what to look for. The report shows what this VIN has on record.

Find the VIN on the driver's door jamb, at the base of the windshield, or on the registration and insurance card.